Printable checklist

How to Apply Varathane Wood Stain

A smooth, even wood stain comes down to good preparation and thin, controlled coats. This illustrated guide covers 3 methods and 34 steps, with a separate picture for every step.

By Co-authored by 52runoob Editorial Team · 34 steps · Hobbies & Crafts · Updated November 19, 2026

Back to the guide
  1. 1. Clear and protect the workspace

    Lay a drop cloth and move obstacles aside so you can work freely.

  2. 2. Clean the wood thoroughly

    Remove dirt and grease with a mild cleaner so the stain can absorb evenly.

  3. 3. Remove old finish if needed

    Strip or sand away any old varnish that would block the new stain.

  4. 4. Sand with the grain

    Work through fine grits in the direction of the grain to avoid cross-grain scratches.

  5. 5. Sand the edges lightly

    Ease sharp edges so they take stain without catching extra colour.

  6. 6. Check for dents and scratches

    Fill deep marks with wood filler before staining so the surface stays even.

  7. 7. Vacuum the dust

    Lift loose dust from the surface and corners before you begin.

  8. 8. Wipe with a tack cloth

    A tack cloth removes the last fine particles that vacuuming leaves behind.

  9. 9. Tape off areas to protect

    Mask any parts you do not want stained, such as metal fittings.

  10. 10. Test on a scrap piece

    Stain an offcut first to check the colour and how much you will need to wipe back.

  11. 11. Stir the stain well

    Mix the can thoroughly so pigment is evenly distributed before you start.

  12. 12. Put on gloves and ventilate

    Protect your hands and open a window or fan while the stain is wet.

  13. 13. Load a clean cloth or brush

    Take a small amount of stain, since less product gives better control.

  14. 14. Apply with the grain

    Wipe or brush along the grain in long, even strokes.

  15. 15. Work in manageable sections

    Stain one area at a time so the product does not dry before you wipe it back.

  16. 16. Keep the coat thin

    A thin coat soaks in evenly while a thick one hides the grain and dries sticky.

  17. 17. Wipe off the excess quickly

    After a minute or two, wipe away surplus stain so the colour stays even.

  18. 18. Even out any dark spots

    Blend heavy patches with a clean cloth before they set.

  19. 19. Let the first coat dry

    Follow the drying time on the can before deciding whether you need another coat.

  20. 20. Apply a second coat if needed

    A second thin coat deepens the colour without hiding the wood grain.

  21. 21. Check the colour in daylight

    Natural light shows the true colour better than a workshop lamp.

  22. 22. Remove the masking tape

    Peel tape away before the stain hardens so edges stay clean.

  23. 23. Confirm the stain is fully dry

    A topcoat over damp stain will trap moisture and peel later.

  24. 24. Sand very lightly

    A gentle once-over with fine sandpaper removes raised grain for a smoother finish.

  25. 25. Remove all sanding dust

    Wipe the surface clean so nothing is sealed into the topcoat.

  26. 26. Choose a compatible topcoat

    Pick a clear finish designed to go over stain, such as polyurethane.

  27. 27. Apply the first thin coat

    Brush or wipe on a thin even layer in the direction of the grain.

  28. 28. Avoid brushing too much

    Excess brushing traps bubbles, so lay the finish on and leave it.

  29. 29. Let it dry as directed

    Give the coat its full drying time before any further sanding or recoating.

  30. 30. Sand between coats lightly

    A very fine sanding helps each new coat bond smoothly to the last.

  31. 31. Add a second topcoat

    Two thin protective coats wear better than one thick one.

  32. 32. Inspect the finish in raking light

    Low-angle light reveals missed spots and uneven areas.

  33. 33. Buff gently when cured

    Once fully cured, a soft cloth brings up a smooth sheen.

  34. 34. Cure fully before heavy use

    Give the finish several days to harden before placing objects on the surface.