Printable checklist

How to Adjust Your Headlights in 12 Easy Steps

Properly aimed headlights help you see the road without dazzling other drivers. This illustrated guide covers 3 methods and 33 steps, with a separate picture for every step.

By Co-authored by 52runoob Editorial Team · 33 steps · Education · Updated November 19, 2026

Back to the guide
  1. 1. Park facing a flat wall

    Place the car perpendicular to a wall on level ground so the beams hit it squarely.

  2. 2. Check the tyre pressures

    Correct tyre pressure keeps the car level, which matters for an accurate beam.

  3. 3. Load the car normally

    Have the usual driver seated and the normal load in the car so the ride height is realistic.

  4. 4. Measure the wall distance

    Park a set distance, such as seven metres, from the wall as a consistent reference.

  5. 5. Mark the centre line

    Use tape to mark the point on the wall directly in front of each headlight.

  6. 6. Mark the target height

    Measure from the floor to the headlight centre and mark that height on the wall.

  7. 7. Draw a lower aiming line

    Mark a line a few centimetres below the headlight height, which is where the beam should land.

  8. 8. Switch on the low beams

    Turn the ignition on and switch to dipped headlights so you can see the current pattern.

  9. 9. Observe the beam outline

    Look at where the bright edge falls against your marks to judge the current aim.

  10. 10. Cover one light at a time

    Mask one headlight so you can adjust the other without confusion.

  11. 11. Find the adjuster screws

    Locate the vertical and horizontal adjusters on top or behind the headlight housing.

  12. 12. Read the owner's manual

    Check which way each screw turns to raise or lower the beam on your model.

  13. 13. Loosen the vertical adjuster

    Turn the upper screw slowly to move the beam up or down toward your mark.

  14. 14. Watch the wall as you turn

    Check the beam after each small turn so you do not overshoot the target.

  15. 15. Set the beam height

    Stop when the bright edge sits on the lower aiming line you marked.

  16. 16. Adjust the horizontal aim

    Use the side screw so the hotspot sits slightly toward the kerb side of the centre.

  17. 17. Match both headlights

    Repeat the same process on the other side so the two beams are even.

  18. 18. Remove the covering cloth

    Uncover the masked light and look at both beams together.

  19. 19. Compare the two patterns

    Both beam edges should meet the wall at the same height and angle.

  20. 20. Recheck the high beams

    Switch to main beam briefly to confirm the pattern stays centred and useful.

  21. 21. Tighten any loose fittings

    Make sure the headlight unit sits firmly so vibration will not spoil your aim.

  22. 22. Clean the lens first

    A dirty lens scatters light and makes a good aim look wrong.

  23. 23. Take a short evening drive

    Drive on a quiet road to see how the beams behave in real conditions.

  24. 24. Check the road ahead

    The beam should light the road clearly without a sharp cutoff too close to the car.

  25. 25. Watch for oncoming drivers

    If other drivers flash you, your beams are probably too high.

  26. 26. Glance at a reflective sign

    A road sign should light up evenly rather than blindingly at eye level.

  27. 27. Pull over and recheck

    Stop on level ground and look at the beam on a nearby surface once more.

  28. 28. Fine-tune if needed

    Make one small adjustment and repeat the check if the beam still sits too high.

  29. 29. Record the final setting

    Note the adjuster positions so you can restore them after future repairs.

  30. 30. Recheck after any front repair

    Any work around the bumper or bonnet can knock the aim out again.

  31. 31. Replace cloudy lenses

    Cloudy plastic lenses need cleaning or restoration to give a clean beam.

  32. 32. Confirm both lights work

    Switch between dipped and main beam to make sure both bulbs respond.

  33. 33. Finish with a safety check

    Step back and confirm the car looks level and the lights sit flush before driving off.